Call, please phone or phone in the picture, we will give you the most sincere quote! Look forward to your call Sales Tel: 13935186687 sales hotline 0351 -5,263,077 of mine pneumatic the concrete vibrator stick FRZ-50/65-wind concrete vibrator for coal mine construction professional, I re-developed on the basis of FH-65-type plug-in the original production and market existing BQF pneumatic submersible pumps, a compressed air as gas source, leaves The wind motor as the driving force new pneumatic concrete vibrator flexible shaft drive. It has a large amplitude, high frequency, light weight, reasonable structure, safe operation, maintenance and easy to use. Independent of supply, humidity and other conditions, in particular, need proof of the place has the the irreplaceable security and reliability of the electric vibrator. Widely used in the construction works of the compressed air source, tamping operations for a variety of dry hard and plastic concrete, cement tamping works particularly applicable side containing gas and coal dust, coal mine and its mine, "set", absolutely safe and reliable to use. Accompanied portable air compressors, the use of a wider range. Uses and characteristics, the vibrator is widely applicable to the compressed air source coal mine well construction, municipal engineering, construction, tunnels, culverts and other field works, a variety of dry concrete products and plastic reinforced concrete cast member The vibrating tamping works particularly applicable, absolutely safe and reliable. 2, has the advantages of compact structure, small size, light weight, low noise, large amplitude, high frequency, and can be adjusted (according to the site requirements, adjust the frequency with the inlet air pressure). 3, the flexible shaft drive, reasonable structure, coupling installation, operation, maintenance, easy to use, without power, humidity and other conditions, it is particularly suitable for special mining conditions. 4, supporting the vibrator rubber hoses 65Mn steel pipe, the club head is made of alloy steel 4OCr,, Polypogon hose connections with of alloys retaining spring or bold, more durable than ordinary vibrator. The main technical parameters Diameter: 50 mm Overall length: 6000 mm (excluding the power section) Power: Vane motor rated speed: 3000 r / min air pressure 0.4 - 0.5 MPa Air Consumption: 1.5 m 3 / min exhaust cross-section: 32 x ?5 (mm) hole into the wind Connector outer diameter: 25 mm vibration frequency (in air): 3000 / min lower amplitude (in air):> 12 mm Weight (with vibrator): 27.5 kg the pneumatic vibration club head diameter: 32,38,50,70 mm available pneumatic vibrator hose shaft length: 4M, 6M, 8M, such as 10m length choice (mine well construction commonly used vibrator 6 meters, spare the rod diameter 50mm, other specifications need to be customized) structure and working principle of the vibrator of the power and vibration of two parts. The dynamic part of the vane pneumatic motor vibrator Ruanzhou head floating insert wind-driven motor shaft head connection kit adapter into one coat will be inserted into the handle until the vibrator. Motor parts: wind-driven rotor, cylinder, on, under cover, bearings and other components. ? The pneumatic motor to the intake side blow, compressed air into the cylinder by cylinder main air duct, push blade, drive the rotor operation for power. ? Cylinder main air duct 8 ?6 hole into the wind, exhaust using 32 ?5 vent intertwined, so that the blades wear uniform. ? The relative increase in the width of the blade and prolong life, five radial rotor equatorial groove milled R75 cutouts of the tank with leaves. ? Pneumatic motor, radial ball bearings were installed under cover 203,305 and thrust ball bearings 51205, radial force and axial torque. Compact structure, sealing, can effectively ensure the reliability, stability and service life of pneumatic motor drive. Use and maintenance of the vibrator wind motor, compact, internal parts with precision, requires the operator to meticulously maintained. Before use to make the exhaust flow, the first test run for 1-3 minutes, check whether the normal operation, flexible start. Without exception, can be put into use. (Such as vibration head does not move, part of the the vibration head and the wind motor gently tapping on the ground can be). 2, the inner diameter of the air intake hose shall be not less than 25mm, the wind pressure shall not be less than 0.3 - 0.4 MPa. Connected to the inlet pipe to pipe joints dirt blowing into the cylinder, in order to avoid impurities cause parts to wear or stuck in the rotor can not operate, will lead to serious cylinder squeeze crack damaged. 4, vibrator use of the process according to the site requirements, you can adjust the vibration frequency control of inlet air pressure. 5, pneumatic the vibrator stop using, not on the water, to prevent debris and sewage into the wind motor. 6, pneumatic motor maintenance, the upper and lower end cap bearing cavity to add a little grease (ZL-3 lithium complex grease), to ensure that the bearing lubrication. 7, such as wind moving motor blades wear serious, will be stuck in the rotor, does not work. You can remove the top cover with M10 screw top on the cover, remove the blade wiper glitches or replaced with new blades. 8, such as long-term storage should disassemble and clean, the degreasing sealed, in order to avoid corrosion. Vibrator use, the Note and maintenance vibrator is a high consumption of products, is in the cast-in-place concrete structures vibrated concrete with coarse aggregate uniform throughout the concrete structures to prevent the hole in the concrete, segregation, a complete vibrator finished by a rubber hose, vibration Polypogon, flexible shaft, oil seal seat 15 accessories. Pneumatic vibrator vibrator flexible shaft floating before use to make the exhaust flow, the first test run for 1-3 minutes, check is functioning properly, the start is flexible. Without exception, can be put into use. The vibrator no vibration, generally vibrator end knock to the ground, can be vibration for a smooth powerful purr vibrated job. 2, vibrator, vibrator should be vertical or inclined inserted into the concrete, the pounding vibration after a certain period of time, the vibration of the vibrator should twitch up and down. Layered pouring on the components or building case, the second layer of vibrators, vibrator should be insert has vibrators layer, in order to eliminate the bed joint, the overall effect. 4 vibrator work continuously for half an hour, you should stop for a period of time to prevent the mechanical heating is enough even damage to the parts. 5, in order to protect the soft pumping hose, use the bending radius should not be less than 500mm. Vibrator every 50-100 hours, disassemble all parts of the rod, cleaning, demolition tip, hose connectors (both left screw) screw, and then struck with a wooden top front hammer extended diameter end of the tapered roller, remove the tapered roller bearings and oil seals. Then remove the hose connector (right screws), you can remove all the parts. 7, after cleaning, replace the damaged pieces, reinstall it. In addition to bearings, all parts must remove oil. The tapered roller cone and casing should ensure that absolutely no oil. 8 installed vibrator, one end of the threaded connections must be tight fight to prevent mortar water to seep into the bar, resulting in weak vibrator. 9, the use of the process of the vibrator, vibrator vibration or weakness, the vibrator apart, check rod oil seal is damaged, such as intact, wipe the casing and cone lane oil, failure can be ruled .